Voltcraft Vc 960 Software Testing

VC920/VC940/VC 960 Computer Interface Software B. Installing vc920940 960 Interface Program To install vc920940 960Interface Program, please follow below procedure: Before install the interface program, make sure that the computer is running the Window 95 or above operating system.Insert the provided CD-ROM into CD-ROM drive.Double-click the My Computer icon from the Windows desktop.Locate the CD-ROM drive from the window, double-click the drive letter to display the folder of vc920940 960.VoltCraft VC-940 protocol reverse engineered. I got another toy to. Sadly, it comes with Windows-only software, which I interpreted as a challenge! Since this is. When I insert my RS-232 tester when running the Windows application, I could see data passing; under MacOSX no data would pass.-Double-click vc920940 960 to display the contents of the folder.Double-click the file Setup.Exe.

Follow the on-screen installation instructions. The installation program will create a DMM Interface Program folder. You will be prompted to select the kind of Program Folder you want to install; you should select “ vc920940 960 Interface Program”. 2 VC920/VC940/VC 960 Computer Interface Software C. Getting Started with vc920940 960 Interface Program To run the vc920940 960 Interface Program, please do the followings: 1.Insert the supplied RS232C (I) interface cable into the slot at the back of the meter and properly connect the other end of the cable to the serial port of computer.

Voltcraft Vc 960 Software Testing Kit

“NO COM” will be displayed on the computer screen if it is not connected properly. From the Windows Start menu, choose Programs DMM Interface Program vc920940 960 3. Press COMSetup to select corresponding COM 1/2/3/4 or connect the USB cable to the Meter then press “USB Connect”. Press Connect from menu bar to start the connection, the icon will be displayed.UNI-T UT71x Status supported Source code Counts 0 IEC 61010-1 CAT III (1000V) / CAT IV (600V) Connectivity / Measurements voltage, resistance, diode, continuity, capacitance, frequency, duty cycle, current, temperature, power (only UT71E), loop current (not on UT71B) Features autorange, hold, peak hold, relative, min/max, bargraph, backlight, true-rms Website The UNI-T UT71x is a series of 0 counts, CAT III (1000V) / CAT IV (600V) handheld digital multimeters with RS232 or USB connectivity. Devices Device Conrad OEM Tenma OEM Counts Comments UNI-T UT71A 20000 UNI-T UT71B 0 UNI-T UT71D Voltcraft VC-960 (?) 40000 UNI-T UT71E 40000 The PCB markings for this series are not necessarily useful, most devices read 'UT71A' (even for devices which are not an UT71A).

However, there is usually a white sticker on some IC which correctly identifies the DMM ('B', 'E', '920', or the like).There's usually also a hand-drawn marking (e. Snowboard Sizing Chart Ride Of The Valkyries. 'B' or 'C') on the PCB itself. Protocol The devices use a simple 11-byte protocol over a USB-to-serial or USBHID-to-serial link (depending on the cable used).

The communication parameters are 2400 baud, 7o1.However, the vendor software opens the serial port with 8n1 settings, so the vendor protocol descriptions are slightly off. Also, the available vendor protocol descriptions from e.g. Conrad are partially incomplete or even erroneous in some places.

Byte Description Comments 0 Digit 1 1 Digit 2 2 Digit 3 3 Digit 4 4 Digit 5 5 Range 6 Function 7 State 1 8 State 2 9 r (0x0d) 10 n (0x0a) The following information is not available/sent via the protocol (and is thus unavailable for sigrok purposes):. the REL, MIN, MAX, HOLD flags.

Voltcraft Vc 960 Software Testing Center

the bargraph value. the backlight status. the low-battery indicator. the internal measurement value store (only available on some models) Resources. Conrad protocol descriptions.